Concrete Protection: Nutech PaveCoat H2O - Repels Water & More! – Epoxy Warehouse

Nutech PaveCoat H2O brings high-performance concrete protection into an environmentally friendly, low-odour formula. Engineered as an advanced water-based acrylic hybrid sealer, PaveCoat H2O deeply penetrates concrete substrates to seal against oil, grease, weather exposure, and everyday wear without the harsh solvent fumes.

Whether you are restoring an old driveway or sealing a newly laid patio, PaveCoat H2O delivers a rich, protective gloss finish that brings out the best in plain concrete, stencil paving, slate, and exposed aggregate. Formulated specifically for Australian conditions, its non-yellowing and UV-resistant chemistry ensures long-lasting colour vibrancy and surface durability under foot and light vehicle traffic.

Unlike traditional solvent sealers, PaveCoat H2O features a low-VOC footprint (<6%) and cleans up effortlessly with warm fresh water, making it safer for applicators, surrounding plants, and residential areas.

Key Features & Highlights

Eco-Friendly & Low Odour: Water-based hybrid formula with low VOC content (<6%) for safer indoor and outdoor application.
UV & Weather Protection: Non-yellowing, fade-resistant gloss finish built to withstand harsh Australian sun exposure.
Stain & Chemical Resistant: Forms a protective barrier that repels oil, grease, water, and household dirt.
Extensive Colour Options: Available in Clear and 46 standard factory colours (with custom colour matching available).
Rapid Recoat Window: Touch dry in 30 minutes and ready for a second coat in just 2 hours at 25°C.
Hassle-Free Clean Up: Equipment, brushes, and rollers clean up easily using warm fresh water.

Typical Applications

PaveCoat H2O is suitable for plain, patterned, and decorative surfaces including:

Residential driveways and carports
Footpaths, walkways, and patio paving
Stencil, stamped, and spray-on concrete
Slate, stone, and exposed aggregate
Tilt-slab panels and cement sheeting

Property	Specification
Chemical Type	Water-based acrylic hybrid
Finish	Gloss (Standard)
VOC Content	<6% (63.6 g/L)
Theoretical Coverage	~6 m²/L per coat
Touch Dry	30 minutes @ 25°C
Recoat Time	2 hours @ 25°C
Full Hard Cure	7 days (No vehicle traffic)
Thinning Agent	Clean fresh water
Clean Up	Warm fresh water
Available Sizes	15L (Clear & Standard Colours) / 14L (Tint Bases)

Application & Substrate Guide

Substrate Compatibility: Suitable strictly for new or old UN-COATED concrete (or for recoating existing PaveCoat H2O finishes).
New Concrete Curing: Allow new concrete to cure for a minimum of 28 days prior to application.
First-Coat Thinning (Water Only):
- Smooth / Steel-Trowelled Concrete: Thin first coat by 50% with clean fresh water to ensure proper penetration.
- Rough / Stipple Finish Concrete: Thin first coat by 20% with clean fresh water.
- Second Coat: Apply un-thinned.

Pavecoat H20 Technical Datasheet Download file

Pavecoat H20 Safety Datasheet Download file

Pavecoat H20 Application Guide Download file

Nutech Antislip Skid Test Download file

Important: Always refer to the manufacturer's latest Product Data Sheet (PDS) and Safety Data Sheet (SDS) for complete substrate preparation, safety guidelines, and application instructions prior to use.

Uncoated Concrete Only: Cannot be applied over existing solvent-based, oil-based, or enamel coatings; applying over incompatible sealers will lead to adhesion failure.
28-Day Concrete Cure Rule: Standard new concrete slabs must cure for at least 28 days before sealer application.
Do Not Etch Soft Concrete: Soft, powdery, or weak concrete surfaces must never be acid-etched or acid-washed, as this will permanently damage the surface profile.
Weather & Temperature Limits: Apply only in dry conditions between 10°C and 30°C. Do not apply if rain is expected within 12 hours, or during early morning/late afternoon when dew and condensation can cause surface clouding.
7-Day Vehicle Curing: Vehicles must strictly not be parked on the newly sealed surface for a minimum of 7 days after application.
Slip Resistance Caution: Sealing smooth or sloping areas can increase slip hazards. Use Nutech AntiSlip Mix In for flat or mild slopes (P2/P3 ratings).
For steep inclines and gradients greater than 1 in 14, a P5 or R12 rating will be required. Nutech Paint recommends EPiC PolyCryl (Exterior & Interior) OR EPiC Epoxy 500 (Interior only) with the addition of the suitable AntiSlip Cast On products for this application. For further information; contact Nutech Paint.

Frequently Asked Questions

Can I pick up PaveCoat H2O from your warehouse?

Yes, pickup is available! While we don't hold every tint and finish at our primary warehouse, we can organize direct pickup from Nutech’s state distribution facilities:

VIC: Seaford (Melbourne)
NSW: Rydalmere (Sydney)
QLD: Meadowbrook (Brisbane)
WA: Cockburn Central (Perth)

Simply select or note your preferred pickup warehouse during checkout, and our team will contact you to confirm stock availability and collection instructions.

Can I apply PaveCoat H2O over existing concrete sealers or paints?

No. PaveCoat H2O is designed strictly for new or old un-coated concrete (or re-coating existing PaveCoat H2O finishes). It is not suitable for overcoating existing solvent-based sealers or enamel coatings.

Do I need to thin PaveCoat H2O for the first coat?

Yes, to ensure deep penetration into the concrete, thin the first coat with clean fresh water according to your floor profile:

Smooth Steel Trowelled Concrete: Thin first coat by 50% with water.
Rough Stipple Concrete: Thin first coat by 20% with water.
Second Coat: Apply un-thinned.

How long must new concrete cure before applying PaveCoat H2O?

New concrete must cure for a minimum of 28 days prior to sealing with PaveCoat H2O. (For same-day sealing on fresh concrete, use PaveCoat Cure & Seal instead)