Sikafloor 264 20KG Kit Including Pigment Paste — Sika Epoxy Suitable for Floors up to 70sqm per Coat
Sikafloor 264 is a premium grade, 100% solids high build multi-purpose, self-smoothing roller applied epoxy floor coating resin designed to protect concrete floors and offer seamless durable floor protection.
Advantages of Sikafloor 264 Epoxy Resin
- Low VOC – 34 grams per litre
- Excellent chemical and mechanical resistance
- Easy application
- Excellent hot tyre pick-up resistance
- Excellent wear and abrasion resistance
- Excellent fuel and chemical resistance
- Produces a smooth and glossy finish — slip resistance can be achieved by adding anti-slip media
- Easy application by brush, roller, squeegee, or spray equipment
- Available in a wide range of colours
Areas of Use
- Garage floors
- Warehouses
- Manufacturing facilities
- Carpark decks
- Clean rooms
- Educational trade facilities
- Aircraft hangars
- Schools
- Mechanical workshops
- Commercial kitchens
Sikafloor 264 — 20kg Kit Contents
Part A: 13.09 kg
Part B: 4.0 kg
Pigment: 2 x 1.15 kg Epoxy Pigment Packs
Total: 19.39 kg / 14.9 Litres
Recommended Preparation Method
Preparation is the key to achieving a long-lasting floor-coating system.
Diamond grinding is the recommended method of preparing new and old substrates prior to applying Sikafloor 264. The purpose is to remove flaking paint and contamination, open concrete pores, and allow the first coat to penetrate deep into the surface.
Acid etching may be used as an alternative. Click here for more information. Hydrochloric acid is available from pool shops or local hardware stores.
Recommended Diamond Tooling Grits
- 30/40 grit for hard concrete
- 80 grit for soft concrete
- PCD plugs to remove flaking paint, then grinding shoes to smooth the floor
Consumption Coverage Guide — 20kg Pigmented Kit Applied Using an 11–12mm Nap Roller
| Area Size | 1st Coat | 2nd Coat | Recommended Minimum Coats | Required Kits |
| Up to 30m² | 10 kg | 9 kg | Two coats | One Kit |
| 30–60m² | 19 kg | 19 kg | Two coats | Two Kits |
| 60–90m² | 29 kg | 29 kg | Two coats | Three Kits |
Notes:
- Use the table above as a guide only — consumption depends on application method and surface porosity
- Additional coats are recommended for floors subject to heavy traffic
- Thin down the first coat by adding 5–7% general-purpose thinners
- Slip resistance can be achieved by adding anti-slip media
Guide to Achieving R or P Rated Slip Resistance
| Slip Rating | P3 or R10 | P4 or R11 | P5 or R12 |
| Recommended Product | Boral 30/60 sand or 80 grit Aluminum Oxide | Boral 1mm sand or 46/30 grit Aluminum Oxide | Boral 1mm sand or 24 grit Aluminum Oxide |
Colour accuracy disclaimer: We have taken care to display the most accurate visuals of our products. However, we are not responsible for the colour accuracy of the device you are viewing our swatches on. These variations arise due to different computer monitors and devices (make, model and technology, as well as resolution, contrast and brightness control settings) in much the same way a scan will differ from an original image and a colour photocopy. Furthermore, coatings can exhibit variation in perceived colour depending on gloss level and application method. If you require a very specific colour match, please make your selection via actual swatches and colour boards available at our showroom.
Product Disclaimer: Ensure you read all product, technical and safety data sheets prior to application as liability falls on the applicator. All products must be applied in accordance with manufacturer’s recommended method.
