{"product_id":"tremco-euco-diamond-hard-densifier-sealer-20l","title":"Tremco EUCO Diamond Hard Clear Satin Concrete Densifier \u0026 Sealer 20L","description":"\u003cp\u003eDiamond Hard Concrete Densifier \u0026amp; Hybrid Concrete Sealer is a penetrating concrete treatment designed to increase the surface density, durability, and abrasion resistance of concrete floors. Supplied by Epoxy Warehouse Australia, Diamond Hard uses a unique blend of silicate and siliconate polymers that penetrate into concrete surfaces and chemically react to create a harder, more durable concrete surface.\u003cspan class=\"\"\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003eUnlike traditional concrete coatings, Diamond Hard does not form a film or membrane over the surface. Instead, it penetrates into the concrete to help reduce water penetration, minimise dusting, and improve the long-term performance of concrete floors while maintaining the existing slip rating.\u003c\/p\u003e\n\u003ch3\u003eWhere Can Diamond Hard Be Used?\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eDiamond Hard concrete densifier and sealer\u003c\/strong\u003e is commonly used for commercial and industrial concrete floors, including:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eWarehouse floors\u003c\/li\u003e\n\u003cli\u003eManufacturing plant floors\u003c\/li\u003e\n\u003cli\u003eDistribution centres\u003c\/li\u003e\n\u003cli\u003eCar parks\u003c\/li\u003e\n\u003cli\u003eCommercial floors\u003c\/li\u003e\n\u003cli\u003eRetail floors\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eIt is suitable for concrete surfaces where improved durability, dust-proofing, easier cleaning, and reduced surface porosity are required.\u003c\/p\u003e\n\u003ch3\u003eKey Benefits of Diamond Hard\u003cspan\u003e\u003c\/span\u003e\n\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003ePenetrating concrete densifier and hybrid sealer\u003c\/li\u003e\n\u003cli\u003eIncreases concrete surface density\u003c\/li\u003e\n\u003cli\u003eImproves abrasion resistance and durability\u003c\/li\u003e\n\u003cli\u003eHelps reduce concrete dusting\u003c\/li\u003e\n\u003cli\u003eReduces water penetration into concrete surfaces\u003c\/li\u003e\n\u003cli\u003eHelps minimise tyre marks\u003c\/li\u003e\n\u003cli\u003eMakes concrete floors easier to clean\u003c\/li\u003e\n\u003cli\u003eNo film-forming coating or membrane\u003c\/li\u003e\n\u003cli\u003eDoes not reduce concrete slip rating\u003c\/li\u003e\n\u003cli\u003eMinimal equipment required for installation\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCoverage\u003c\/h3\u003e\n\u003cp\u003eApproximate usage rate:\u003cspan\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e0.2mm wet application thickness\u003c\/li\u003e\n\u003cli\u003eApproximately 5m²\/L on concrete\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 class=\"\"\u003eDrying Time \u0026amp; Return to Traffic\u003cspan\u003e\u003c\/span\u003e\n\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDrying time at 25°C and 50% RH: \u003cstrong\u003e4–6 hours\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eReturn to traffic: \u003cstrong\u003e24 hours\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003eDrying and return-to-service times may vary depending on site conditions, temperature, humidity, and substrate conditions.\u003c\/em\u003e\u003c\/p\u003e\n\u003ch3\u003eSurface Preparation\u003cspan\u003e\u003c\/span\u003e\n\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eConcrete shall be water-cured and attain a \u003cstrong\u003e20 MPa minimum compressive strength\u003c\/strong\u003e.\u003c\/li\u003e\n\u003cli\u003eConcrete shall be free of any laitance which may inhibit sufficient adhesion. Removal of laitance can be achieved through a variety of physical abrasion methods, such as:\n\u003cul\u003e\n\u003cli\u003eShot blasting (preferred method)\u003c\/li\u003e\n\u003cli\u003eSandblasting\u003c\/li\u003e\n\u003cli\u003eGrinding\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eConcrete surface shall be properly cleaned so that the surface to receive the \u003cstrong\u003eDiamond Hard\u003c\/strong\u003e is free of:\n\u003cul\u003e\n\u003cli\u003eMould\u003c\/li\u003e\n\u003cli\u003ePaint\u003c\/li\u003e\n\u003cli\u003eSealers\u003c\/li\u003e\n\u003cli\u003eCoatings\u003c\/li\u003e\n\u003cli\u003eCuring agents\u003c\/li\u003e\n\u003cli\u003eLoose particles\u003c\/li\u003e\n\u003cli\u003eOther contamination or foreign matter that may interfere with adhesion\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eSpalled areas shall be cleaned free of loose contaminants prior to repair. Because jobsite conditions vary, it is recommended that you contact your local Tremco Representative. Depending on the substrate and depth of the spalled areas, a \u003cstrong\u003eTREMcrete repair product\u003c\/strong\u003e will be recommended as the best method of repair.\u003c\/li\u003e\n\u003cli\u003eIn the event of exposed reinforcing steel, it is recommended that the structural engineer of record be contacted for investigation and for the best repair method.\u003c\/li\u003e\n\u003cli\u003eSurfaces shall be made free of defects, as they will telegraph and show through the \u003cstrong\u003eDiamond Hard\u003c\/strong\u003e.\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eAll drains shall be cleaned and operative. Drains shall be recessed lower than the deck surface. The surface shall be sloped to drain to provide positive drainage (\u003cstrong\u003e1:100\u003c\/strong\u003e) as per \u003cstrong\u003eAS4654.2\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eDrains should be detailed as instructed below:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCut a \u003cstrong\u003e6mm wide x 12mm deep keyway\u003c\/strong\u003e into the concrete surface at any point where the coating will have an exposed terminating edge.\u003c\/li\u003e\n\u003cli\u003eThis includes areas where the coating will end in an open area subject to traffic, such as:\n\u003cul\u003e\n\u003cli\u003eEnd of ramps\u003c\/li\u003e\n\u003cli\u003eAround drains\u003c\/li\u003e\n\u003cli\u003eAlongside expansion joints\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eIf the project is a restoration deck, old sealant and membrane material shall be removed. The joint interface will require thorough:\n\u003cul\u003e\n\u003cli\u003eWire brushing\u003c\/li\u003e\n\u003cli\u003eGrinding\u003c\/li\u003e\n\u003cli\u003eSandblasting\u003c\/li\u003e\n\u003cli\u003eSolvent washing and\/or primer\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eMethod of Application\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eSubstrate temperature during application must be between \u003cstrong\u003e10°C and 38°C\u003c\/strong\u003e.\n\u003cul\u003e\n\u003cli\u003eAt temperatures below 10°C, the reaction and “gelling” process of Diamond Hard is significantly slower. The concrete will need to remain wet with Diamond Hard for a significantly longer period of time.\u003c\/li\u003e\n\u003cli\u003eIn hot or windy conditions, the reaction may take less than the normal 30–60 minute period.\u003c\/li\u003e\n\u003cli\u003eConcrete should be pre-dampened in hot weather. Apply Diamond Hard when all ponding water has evaporated.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eApply \u003cstrong\u003eDiamond Hard\u003c\/strong\u003e to the concrete surface by:\n\u003cul\u003e\n\u003cli\u003eLow-pressure sprayer, or\u003c\/li\u003e\n\u003cli\u003ePouring directly onto the surface and distributing evenly by broom or squeegee\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eUsing soft bristle brooms or brushes on an auto-scrubber, work the \u003cstrong\u003eDiamond Hard\u003c\/strong\u003e around the treated area and into the concrete surface.\u003c\/li\u003e\n\u003cli\u003eThe concrete must be kept wet with \u003cstrong\u003eDiamond Hard\u003c\/strong\u003e for at least \u003cstrong\u003e30 minutes\u003c\/strong\u003e.\n\u003cul\u003e\n\u003cli\u003eIf necessary, add additional Diamond Hard to maintain a wet surface.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eContinue the application process until the entire floor has been treated.\u003c\/li\u003e\n\u003cli\u003eWhen finished, completely remove all excess \u003cstrong\u003eDiamond Hard\u003c\/strong\u003e from the surface.\n\u003cul\u003e\n\u003cli\u003eIf excess Diamond Hard is allowed to dry on the concrete surface, a white residue will form that can only be removed by mechanical means such as:\n\u003cul\u003e\n\u003cli\u003eGrinding\u003c\/li\u003e\n\u003cli\u003eSanding\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eBuy Diamond Hard from Epoxy Warehouse Australia\u003cspan\u003e\u003c\/span\u003e\n\u003c\/h3\u003e\n\u003cp\u003eDiamond Hard Concrete Densifier \u0026amp; Hybrid Concrete Sealer is available from Epoxy Warehouse Australia for commercial and industrial concrete floor applications. We supply genuine products with technical information and support to help you choose the right concrete treatment solution for your project.\u003c\/p\u003e\n\u003cp\u003eAlways refer to the latest Diamond Hard Product Datasheet and Safety Data Sheet before application.\u003c\/p\u003e","brand":"Tremco","offers":[{"title":"Default Title","offer_id":45521212932182,"sku":"A1AMY600035","price":296.19,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0694\/4836\/8214\/files\/Tremcodiamondhardconcretedensifier.jpg?v=1785900724","url":"https:\/\/epoxywarehouse.com.au\/products\/tremco-euco-diamond-hard-densifier-sealer-20l","provider":"Epoxy Warehouse | Epoxy Floor Coating Supplier","version":"1.0","type":"link"}