Sikafloor 050 Ramp and Patch 20kg

High strength, fast setting mortar

$65.00 inc GST

Quantity:
SKU: FAAA41 Categories: , , ,

Description

Description

Sikafloor®-050 Ramp and Patch is a fast setting ramping / patching mortar used for internal & external concrete surfaces.

USES

  • Applied by its self, or part of a system with suitable materials from Sikafloor®, Sikadur® SikaBond®, SikaTite® & Davco® ranges
  • Ramping/grading to create a smooth transition between two types of flooring
  • Patching damaged concrete floors, stairs, & walls

 

CHARACTERISTICS AND ADVANTAGES

  • Very Low VOC (1 grams per litre)
  • Rapid drying
  • Internal & external applications
  • Non-combustible
  • Fast setting
  • Smooth flat surface is achievable
  • High early strength 24hrs = 28 – 30MPa
  • Walkable in as little as 40 – 50 minutes
  • Installation of flooring in 60-90 minutes

 

COLOUR
Grey Powder

 

PACKAGING
20kg Bag – 48 bags per pallet

 

EQUIPMENT
High speed heavy duty electric drill and mixing paddle. Suitable size bucket/vessel – 20L +

 

MIXING
Mix the entire 20kg bag of powder with 4.1 – 4.3 Litres of clean, cool water. Slowly add powder to the water while mixing with a suitable electric drill and mixing paddle. Thoroughly mix for only 1 minutes to a lump free consistency and apply directly. Not mixing for the recommended time or additional water may result in product irregularities and possible product failure.

 

APPLICATION
Using Sikafloor®-050 Ramp and Patch prior to floor coverings:
Ramping:
Once product is mixed immediately apply and begin working to heights required. Product can be worked/shaped/shaved with the back of a trowel up to 20 minutes after application.

Using Sikafloor®-050 Ramp and Patch to repair concrete:
Patching concrete
On a well prepared clean and roughened concrete surface a bonding primer is generally not required, but pre-dampening of the surface with
water is recommended. After water has been applied and allowed to soak the concrete surface should achieve a dark matt appearance without
glistening and surface pores and pits shall not contain water. The surface shall not be allowed to completely dry before application of Sikafloor®-050 Ramp and Patch. If priming is preferred first diluted Sikafloor® 01 Primer 1:3 with water then apply by way of a brush till all areas have been coated and allow to dry. Once placed, a trowel is used to pack & shape Sikafloor®-050 Ramp and Patch into the concrete void. Sikafloor®-050 Ramp and Patch can also be left high of the finished surface required and shaved using the trowel until full set. Working time 15 – 20 min @ 23°C. Note: Freshly applied Sikafloor®-050 Ramp and Patch must be protected from damp, condensation and all forms of water while curing for at least 24 hours.

 

Sikafloor 050 Ramp and Patch Data Sheets

 

 

Sikafloor®-050 Ramp and Patch – Sika’s Website

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Sikafloor 050 Ramp and Patch 20kg”

Your email address will not be published. Required fields are marked *

Disclaimer

Colour accuracy disclaimer: We have taken care to display the most accurate visuals of our products. However, we are not responsible for the colour accuracy of the device you are viewing our swatches on. These variations arise due to different computer monitors and devices (make, model and technology, as well as resolution, contrast and brightness control settings) in much the same way a scan will differ from an original image and a colour photocopy. Furthermore, coatings can exhibit variation in perceived colour depending on gloss level and application method. If you require a very specific colour match, please make your selection via actual swatches and colour boards available at our showroom.

Product Disclaimer: Ensure you read all product, technical and safety data sheets prior to application as liability falls on the applicator. All products must be applied in accordance with manufacturer’s recommended method.